Россия +7 (495) 204-29-64
Казахстан +7 (727) 350-81-84

Описание

Preparation of filter FIPA 1-0,5-0,6 to work

1. Before loading of the filter material in the filter FIPA 1-0,5-0,6 you must verify that the upper and lower switching devices of 0,5 FIPA filter holes are not clogged and the system works evenly.
2. Sodium-cationite filter FIPA 1-0,5-0,6 used filter materials such as sulfonated and cation exchange resin KU-2.
3. To prevent damage to the caps, the first layer of cation exchange resin (20-40 mm) put in the filter FIPA 1-0,5-0,6 with extreme caution. Cation-exchangers that have significant ability to swell, to load in a filter of 0.5 FIPA is required only partially filled with water. Uploaded to filter FIPA 1-0,5-0,6 cation must not contain any dust particles with a diameter less than 0.25 mm. However, the cation content of not more than 5% is allowed to download, but in this case, the pulverized particles is necessary when setting up the filter to remove by rinsing with water flow upwards. The coefficient of heterogeneity of the grains of the cation exchange resin should be at least 2.
4. Loading of cation exchange resin necessary to produce layers 75-100 mm.
5. After laying of each layer in the filter FIPA 1-0,5-0,6, it is necessary to aerate the water flow from the bottom up, and to clean out dust particles before the complete clarification of the wash water.
6. Loading of cation exchange resin in the filter FIPA 1-0,5-0,6 it is necessary to conduct only as long as its surface in the filter 0,5 FIPA will not be on 70-100 mm below the design level.
7. Next, you need again to loosen all of the layer of cation within 20-35 minutes. After backwashing, the water in the filter FIPA 1-0,5-0,6 drops below the surface of the cation exchange resin and the upper layer (30-35 mm) is removed from the filter.
8. The hatch filter FIPA 0,5 zabolit and proceed to the washing of the cation from the acid.

The working procedure of cationite filters of the type FIPA 1-0,5-0,6

1. Work cationite filters of the type FIPA 1-0,5-0,6 is to periodically performing the following operations constituting a complete work cycle of the filter:
- softening of the treated water;
- Wrigley cation;
- regeneration of cation exchange resin;
- washing of the cation exchanger.
2. Wrigley of cation exchange resin in the filter FIPA 1-0,5-0,6 to produce necessary before each regeneration by the rising current of clear water. To do this, open the valves on the water feed line to the filter FIPA 0.5 and on the vent. Then slowly open the valve of the pipeline foaming water. The duration of backwashing is 15-30 min. at an intensity of 3-5 l/m2, and is controlled by the degree of light drain of water in the drainage. If after 15 minutes after the start of backwashing water clarification does not occur, then Wrigley water should continue. After backwashing, you must close the valve on the return line, and then the valve on the supply line of the source water to the filter.
3. After backwashing, the cation exchange resin in the filter FIPA 0,5 to regenerate the salt solution to restore exchange ability. Next, you need to open the valve on the pipeline of regeneration salt solution and the valve on the discharge line of the regeneration solution. The duration of regeneration of cation exchanger is 10-15 min During regeneration to ensure that the filter FIPA 1-0,5-0,6 was the staking of water, which is checked with air vent and pressure gauge.
4. At the end of the feed salt solution to carry out washing of the cation exchanger. Next, you need to close the valve on the pipeline of salt and open the valve in the upper piping of the source water. The washing of the cation lead to until the stiffness of the drain water outlet from the filter FIPA 1-0,5-0,6 would not meet the norm.
5. Softening of treated water. When the filter 0,5 FIPA should always be the backwater of the water. 2-3 times per shift by means of vent, you need to check for pressurization and to remove the accumulated air. During operation of the filter FIPA 1-0,5-0,6 to periodically take samples of the softened water for analysis. With increasing hardness of softened water to a value exceeding the limit filter FIPA 1-0,5-0,6 must be disabled on the regeneration, i.e., to repeat the operations described above.

Характеристики

ХарактеристикаЗначение
 Ступень очистки  1 ступень
 Производительность, м3/ч  10
 Условный диаметр фильтра, мм  500
 Тип верхнего распределительного устройства (ВРУ)  стакан
 Материал верхнего распределительного устройства  нержавеющая сталь
 Тип нижнего распределительного устройства (НРУ)  ложное дно
 Материал нижнего распределительного устройства  нержавеющая сталь
 Кол-во колпачков в НРУ 1/2", шт.  10
 Высота фильтрующей загрузки, не более, мм  1400
 Рабочее давление, МПа  0,6
 Температура в фильтре, не более, С  90
 Масса, кг  307

Документация

ГОСТы и сертификаты

ТР ТС 010/2011 - Декларация о соответствии на подогреватели мазута ЕАЭС N RU Д-RU.KA1.B.04314/19

Фотогалерея

Comments ()

  1. Fsthss 13 november 2018, 10:32(Comment was edited) # 0
    At the end of the feed salty solution to carry out washing of the cation exchanger. Next, you need to close the valve on the stainless steel round pipe of salt and open the valve in the upper piping of the source water.

    Filter FIPA 1-0,5-0,6 in stock: IRAS: about the bottom + stainless caps; temporary: a glass of stainless steel. steel; without piping, valves, backfill material

    Before loading of the filter material in the filter FIPA 1-0,5-0,6 you must verify that the upper and lower switching devices of 0,5 FIPA filter holes are not clogged and the system works evenly.
    Документация

    85 300 руб.
    Все цены указаны с учетом НДС 20%
    - +
    Поделиться:

    Просмотренные товары