Россия +7 (495) 204-29-64
Казахстан +7 (727) 350-81-84

Описание

The working procedure of cationite filters of the type FIPA 1-3,0-0,6

1. Work cationite filters of the type FIPA 1-3,0-0,6 is to periodically performing the following operations constituting a complete work cycle of the filter:
- softening of the treated water;
- Wrigley cation;
- regeneration of atianta;
- washing of the cation exchanger.
2. Wrigley of cation exchange resin in the filter FIPA 1-3,0-0,6 to produce necessary before each regeneration by the rising current of clear water. To do this, open the valves on the water feed line to the filter FIPA 3.0 and on the vent. Then slowly open the valve of the pipeline foaming water. The duration of backwashing is 15-30 min. at an intensity of 3-5 l/m2, and is controlled by the degree of light drain of water in the drainage. If after 15 minutes after the start of backwashing water clarification does not occur, then Wrigley water should continue. After backwashing, you must close the valve on the return line, and then the valve on the supply line of the source water to the filter.
3. After backwashing, the cation exchange resin in the filter FIPA 3,0 to regenerate the salt solution to restore exchange ability. Next, you need to open the valve on the pipeline of regeneration salt solution and the valve on the discharge line of the regeneration solution. The duration of regeneration of cation exchanger is 10-15 min During regeneration to ensure that the filter FIPA 1-3,0-0,6 was the staking of water, which is checked with air vent and pressure gauge.
4. At the end of the feed salt solution to carry out washing of the cation exchanger. Next, you need to close the valve on the pipeline of salt and open the valve in the upper piping of the source water. The washing of the cation lead to until the stiffness of the drain water outlet from the filter FIPA 1-3,0-0,6 would not meet the norm.
5. Softening of treated water. When the filter of 3.0 FIPA should always be the backwater of the water. 2-3 times per shift by means of vent, you need to check for pressurization and to remove the accumulated air. During operation of the filter FIPA 1-3,0-0,6 to periodically take samples of the softened water for analysis. With increasing hardness of softened water to a value exceeding the limit filter FIPA 1-3,0-0,6 must be disabled on the regeneration, i.e., to repeat the operations described above.

Характеристики

ХарактеристикаЗначение
 Ступень очистки  1 ступень
 Производительность, м3/ч  180
 Условный диаметр фильтра, мм  3000
 Тип верхнего распределительного устройства (ВРУ)  лучевая система
 Материал верхнего распределительного устройства  ст3сп5
 Тип нижнего распределительного устройства (НРУ)  ложное дно
 Материал нижнего распределительного устройства  пластик
 Высота фильтрующей загрузки, не более, мм  2500
 Рабочее давление, МПа  0,6
 Температура в фильтре, не более, С  40
 Масса, кг  5 500

Документация

ГОСТы и сертификаты

ТР ТС 010/2011 - Декларация о соответствии на подогреватели мазута ЕАЭС N RU Д-RU.KA1.B.04314/19

Фотогалерея

Comments ()

    Filter FIPA 1-3,0-0,6, comprising: ANR: false bottom + plastic caps; lying: a radiation system St3; without piping, valves, backfill material

    Work cationite filters of the type FIPA 1-3,0-0,6 is to periodically performing the following operations constituting a complete work cycle of the filter: - softening of the treated water; - Wrigley cation; - regeneration of atianta; - washing of the cation exchanger.
    Документация

    970 000 руб.
    Все цены указаны с учетом НДС 20%
    - +
    Поделиться:

    Просмотренные товары