Россия +7 (495) 204-29-64
Казахстан +7 (727) 350-81-84

Описание

Preparation of filter FIPA 2-1,5-0,6 to work

1. Before loading of the filter material in the filter FIPA 2-1,5-0,6 you must verify that the upper and lower switching devices of the filter FIPA 1.5 holes are not clogged and the system works evenly.
2. Sodium-cationite filter FIPA 2-1,5-0,6 used filter materials such as sulfonated and cation exchange resin KU-2.
3. To prevent damage to the caps, the first layer of cation exchange resin (20-40 mm) put in the filter FIPA 2-1,5-0,6 with extreme caution. Cation-exchangers that have significant ability to swell, to load in a filter of 1.5 FIPA is required only partially filled with water. Uploaded to filter FIPA 2-1,5-0,6 cation must not contain any dust particles with a diameter less than 0.25 mm. However, the cation content of not more than 5% is allowed to download, but in this case, the pulverized particles is necessary when setting up the filter to remove by rinsing with water flow upwards. The coefficient of heterogeneity of the grains of the cation exchange resin should be at least 2.
4. Loading of cation exchange resin necessary to produce layers 75-100 mm.
5. After laying of each layer in the filter FIPA 2-1,5-0,6, it is necessary to aerate the water flow from the bottom up, and to clean out dust particles before the complete clarification of the wash water.
6. Loading of cation exchange resin in the filter FIPA 2-1,5-0,6 it is necessary to conduct only as long as its surface in the filter is 1.5 FIPA will not be on 70-100 mm below the design level.
7. Next, you need again to loosen all of the layer of cation within 20-35 minutes. After backwashing, the water in the filter FIPA 2-1,5-0,6 drops below the surface of the cation exchange resin and the upper layer (30-35 mm) is removed from the filter.
8. The hatch filter FIPA 1,5 zabolit and proceed to the washing of the cation from the acid.

Характеристики

ХарактеристикаЗначение
 Ступень очистки  2 ступень
 Производительность, м3/ч  100
 Условный диаметр фильтра, мм  1500
 Тип верхнего распределительного устройства (ВРУ)  стакан
 Материал верхнего распределительного устройства  ст3сп5
 Тип нижнего распределительного устройства (НРУ)  ложное дно
 Материал нижнего распределительного устройства  пластик
 Кол-во колпачков в НРУ 1/2", шт.  130
 Высота фильтрующей загрузки, не более, мм  1500
 Рабочее давление, МПа  0,6
 Температура в фильтре, не более, С  40
 Масса, кг  1 800

Документация

ГОСТы и сертификаты

ТР ТС 010/2011 - Декларация о соответствии на подогреватели мазута ЕАЭС N RU Д-RU.KA1.B.04314/19

Фотогалерея

Comments ()

    Filter FIPA 2-1,5-0,6 in stock: IRAS: about the bottom + plastic caps; temporary: a glass of St3; without piping, valves, backfill material

    To prevent damage to the caps, the first layer of cation exchange resin (20-40 mm) put in the filter FIPA 2-1,5-0,6 with extreme caution. Cation-exchangers that have significant ability to swell, to load in a filter of 1.5 FIPA is required only partially filled with water.
    Документация

    294 600 руб.
    Все цены указаны с учетом НДС 20%
    - +
    Поделиться:

    Просмотренные товары